Publicada em 17 de nov. de 2026 · Verificamos em 17 de nov. de 2026 que ainda está no ar
Essa empresa é sua?US$ 30 – US$ 250 por projeto
4-Layer ESP32 Hardware completion & Thermal Simulation (Current: 80% Schematic) ===================================== This is not a simple project it requires high level of expertise ================================ PROJECT BUDGET & BIDDING TERMS: • Budget: Strict Fixed Price between $40.00 USD and $60.00 USD. • Selection Criteria: The best, most technically sound proposal strictly within this budget range ($40 - $60) will be awarded immediately. • NDA Required: A signed NDA is mandatory prior to releasing existing KiCad schematic source files. • Notice: Bids exceeding $60 or generic placeholder bids will be ignored automatically. • Anti-Spam Check: Start your proposal with the exact passphrase: "TITAN-VALIDATED". ===================================================================== ### Project Overview: We are seeking a Senior Hardware / Embedded Electronics Engineer to perform an end-to-end design audit, simulation, schematic completion, 4-layer PCB layout, and thermal/reliability validation for an industrial-grade ESP32 controller board. Schematic is currently ~85% complete in KiCad. --- ### Appendix A: Scope of Work and Deliverables #### Milestone 1: Schematic Audit, Peripheral Integration & Electrical Simulation ##### A. Scope of Work (Milestone 1) 1. **Circuit Simulation & Power Integrity (PI/PDN):** - Full audit of current KiCad schematic; fix industrial design flaws. - Simulate and validate critical sub-circuits, transient behavior, and PDN stability in Siemens HyperLynx / LTspice before routing. - PDN/PI analysis: Optimize plane impedance, decoupling capacitor selection/placement, voltage stability, and noise suppression across all rails. - Startup and transient load noise analysis. 2. **Schematic Review & Hardware Integration:** - **BOM Optimization:** Replace high-cost, long lead-time, single-source, or NRND/EOL parts with active, reliable, dual-sourced alternatives (DigiKey/Mouser/LCSC) without compromising performance. - **MCU & Module Interfacing:** - Route 2 spare HLK GPIOs to ESP32 EN & GPIO0; connect HLK UART to ESP32 UART0 (shared GND) for boot mode control/reflashing via HLK (verify pull-ups/debounce prevent accidental bootloader entry on HLK reboot). - Route HLK USB lines to add a MicroSD card slot. - Add 1x PoE RJ45 connector & 12V output DC barrel jack. - Add 1x RS485 connector using THVD1400D transceiver. - Add ES7210 (4-ch differential ADC) for 2x differential analog MIC inputs. - Add 2x MAX98357A (mono I2S Class-D amps on shared I2S bus, split via SD_MODE) for 2x Class-D BTL speaker outputs (verify zero pin conflicts with strapping, flash, or RS485). - **Added I/O & Connectors:** - 1x Illuminated ON/OFF Switch Connector (JST): Low-side N-Channel MOSFET for LED, hardware RC debounce (10kΩ pull-up + 100nF cap), TVS ESD clamping diode. - 4x Dry-Contact Sensor Connectors (2-Pin JST): Hardware RC debounce (10kΩ + 100nF) + bidirectional TVS ESD diodes on each. - 2x Active Sensor Connectors (3-Pin JST: VCC, GND, SIG): Resettable PTC Polyfuse on VCC, 100nF decoupling, TVS ESD diode on signal. - **COTS Peripherals Specification (Dedicated BOM Section):** - Select and specify manufacturer MPNs, datasheets, sourcing links, and mating pre-crimped JST harnesses for: (1) 2x IP65/IP67 enclosed cavity speakers (8Ω 2W) (2) 2x IP67 waterproof analog ECM mic capsules (silicone boots + hydrophobic membrane) (3) 1x IP65/IP67 illuminated metal momentary/latching pushbutton (O-ring sealed) (4) 4x IP67 waterproof door reed switches (5) 2x outdoor weather-sealed active motion sensors (PIR / 24GHz mmWave radar 0-1m). - **Hardware Design Constraints:** - Polarized/keyed connectors (JST-XH 2.54mm or JST-PH 2.0mm) with clear Pin 1 silk screen. - TVS diodes placed immediately adjacent to connector pins ahead of MCU tracks. - **Power Architecture & Sequencing:** - 12V, 5V, and 3.3V rails must fully stabilize before ESP32 EN/Reset is pulled high (brownout prevention). - TPS e-fuse & buck stages: Soft-start and inrush current limiting under high capacitive loads. - Connect TPS PG pin to buck converter EN pins and to ESP32 GPIO. - Verify resistor divider on TPS EN line (UVLO protection, max 7V rating). - Connect TPS LDSTRT to ESP32 GPIO via timer logic for startup handshake. - Connect PG pin of each buck converter to separate ESP32 GPIOs; TPS IMON to ADC-capable GPIO. 3. **Safety & Isolation:** - Establish galvanic isolation strategy, defining creepage and clearance rules between high-power AC/DC tracks and low-voltage logic/RF sections. ##### B. Milestone 1 Deliverables - Fully organized, unencrypted KiCad schematic source files and custom project libraries (symbols/footprints). - Preliminary Production BOM & External COTS Build BOM (Excel/CSV with MPNs, lifecycle status, sourcing links). - ERC Report (zero critical violations). - Native simulation files (.hyp, .asc, or LTspice profile files) and exported waveform/impedance reports. - Preliminary Isolation & Safety Design Note (creepage/clearance). --- #### Milestone 2: 4-Layer PCB Layout, Thermal/Reliability Simulation & Production Package ##### A. Scope of Work (Milestone 2) 1. **PCB Design & Layout (4-Layer):** - Industrial DFM/DFA compliant layout. - Dedicated AGND and DGND separation for ES7210 and MAX98357A, tied at a single star-ground point to eliminate audio hum and switching noise. - Strict galvanic isolation and clearance between high-power tracks and low-voltage logic/RF. - Full compliance with Espressif hardware design guidelines for ESP32 module placement and RF keepout. 2. **Thermal & Reliability Simulation:** - Full FEA/CFD Thermal Simulation (ANSYS Icepak or Siemens Simcenter Flotherm) under continuous 24/7 load across -10°C to +65°C ambient. - Reliability assessment for up to 95% RH humidity and component derating (capacitors ≥105°C, voltage derated by 20-30%) proving 5+ years operational lifetime (Arrhenius / IPC-9592 standards). - Identify hotspots (HLK module, power stages) and apply mitigations (thermal vias, copper pours).
Crie uma conta grátis pra ver a vaga completa e se candidatar.